View 12-22-Y2G6C-A30-2C_280376.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
Right Angle Lens Chip LED with Bi-Color(Multi-color) 12-22/Y2G6C-A30/2C
Features
Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Multi-color type. Pb-free. The product itself will remain within RoHS compliant version.
Descriptions
The 12-22 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc.
Applications
Backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use.
Device Selection Guide
Chip Type Y2 G6 Material AlGaInP AlGaInP Emitted Color Brilliant Yellow Brilliant Yellow Green Water Clear Lens Color
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 1 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Package Outline Dimensions
A
Y
A
2.0 3.0
1.0
B
C1 C2
(-) (-)
(+)
Polarity
A
1.0
For reflow soldering (propose)
1.5 3.5 0.9 0.65
R0.44
Cathode mark
A
1.5
A
0.9
A
Note: The tolerances unless mentioned is 0.1mm,Unit = mm
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 2 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Absolute Maximum Ratings (Ta=25)
Parameter Reverse Voltage Forward Current Peak Forward Current (Duty 1/10 @1KHz) Power Dissipation Symbol VR IF IFP Pd Rating 5 Y2:25 G6:25 Y2:60 G6:60 Y2:60 G6:60 Y2:2000 G6:2000 -40 ~ +85 -40 ~ +90 Unit V mA
mA mW
Electrostatic Discharge(HBM) Operating Temperature Storage Temperature
ESD Topr Tstg
V
Reflow Soldering : 260 for 10 sec. Soldering Temperature Tsol Hand Soldering : 350 for 3 sec.
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 3 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Electro-Optical Characteristics (Ta=25)
Parameter Symbol Y2 Luminous Intensity Viewing Angle Peak Wavelength IV G6 21/2 Y2 p G6 Y2 Dominant Wavelength d G6 Y2 Spectrum Radiation Bandwidth G6 Y2 Forward Voltage VF G6 Y2 Reverse Current IR --------10 1.7 2.0 2.4 10 A VR=5V 1.7 ----20 2.0 2.4 V ----573 15 ----nm ------------575 589 ----nm IF=20mA 28.5 --------120 591 ----nm 72.0 ----deg Min. 45.0 Typ. ----Max. 112 mcd Unit Condition
G6 Notes:
1.Tolerance of Luminous Intensity 11%
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 4 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Bin Range Of Luminous Intensity
Y2
Bin P Q Min 45.0 72.0 Max 72.0 mcd 112 IF=20mA Unit Condition
G6
Bin N P Min 28.5 45.0 Max 45.0 mcd 72.0 IF=20mA Unit Condition
Notes:
1.Tolerance of Luminous Intensity 11%
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 5 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Typical Electro-Optical Characteristics Curves Y2
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 6 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Typical Electro-Optical Characteristics Curves G6
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 7 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Label explanation
CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank
xxxxxx xxxxxx
RoHS
xxxxxxxxxxxx xxxx xxxxxxxx
Reel Dimensions
Note: The tolerances unless mentioned is 0.1mm, Unit = mm
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 8 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned is 0.1mm, Unit = mm
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Desiccant
Label
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 9 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10%
No. 1
Items Reflow Soldering
Test Condition Temp. : 2605 Min. 5sec. H : +100 15min 5 min L : -40 15min H : +100 5min 10 sec L : -10 5min Temp. : 100 Temp. : -40 IF = 20 mA 85/ 85%RH
Test Sample Hours/Cycles Size 6 Min. 300 Cycles 22 PCS.
Ac/Re 0/1
2
Temperature Cycle
22 PCS.
0/1
3
Thermal Shock High Temperature Storage Low Temperature Storage DC Operating Life High Temperature / High Humidity
300 Cycles 1000 Hrs. 1000 Hrs. 1000 Hrs. 1000 Hrs.
22 PCS.
0/1
4 5 6 7
22 PCS. 22 PCS. 22 PCS. 22 PCS.
0/1 0/1 0/1 0/1
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 10 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
Precautions For Use
1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LED's floor life is 1 year under 30 or less and 60% RH or less. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 11 of 12
Prepared by:Lu zhongwei
EVERLIGHT ELECTRONICS CO.,LTD.
12-22/Y2G6C-A30/2C
4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com
Everlight Electronics Co., Ltd. Device No:SZDSE-122-A15
http://www.everlight.com Prepared date:21-Dec-2006
Rev 1
Page: 12 of 12
Prepared by:Lu zhongwei

▲Up To Search▲

Price & Availability of 12-22-Y2G6C-A30-2C

	To Download 12-22-Y2G6C-A30-2C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .